In the design process, the transmitter uses the S8050 amplifier, which is a power amplifier that amplifies its audio signal. The receiving part uses a common low-power audio amplifier D2822A, which forms the core of the infrared communication device. The device has almost no distortion in speech transmission, the transmission distance meets the requirements, and the operation is simple. When adding a relay forwarding point, changing the direction of 90 degrees, the effect is good.
1. Overall design of the program
1.1 System overall design block diagram
The earphone is composed of a transmitting module and a receiving module. Transmitter module: mainly includes basic circuit and infrared light-emitting diode, which is mainly driven by 5V voltage, and the audio signal is driven by the basic circuit to drive the infrared light-emitting diode to emit the signal. Receiver module: mainly includes S8050 power amplifier and its surrounding auxiliary components. It mainly transmits the received signal through D2822A power under the driving of 5V voltage, and then drives the speaker to emit sound, so that the listener can hear the transmitter. music.
The overall principle block diagram of the system is shown in Figure 1.1.
1.2 unit circuit design
1.2.1 Transmitting part of the circuit
The sound signal is taken from the audio output socket of the MP3 or signal generator. The audio signal output by MP3 is coupled to VT1 S8050 through capacitor C1 for one-stage amplification to drive infrared light-emitting diodes. VD1 and VD2 emit light, and the change of sound signal causes changes in the luminous intensity of VD1 and VD2, that is, the luminous intensity of VD1 and VD2 is affected by sound. modulation. The DC 5V voltage flows through the resistor R4 to VT1, and then supplies the operating voltage, amplifies the audio signal to drive the VD1 and VD2 to emit light, and transmits the signal.
The transmitting circuit is shown in Figure 1.2.
1.2.2 Receiving part of the circuit
The receiving part of the circuit uses a piece of audio amplification integrated circuit D2822A for power amplification. There is an infrared receiving tube. When the infrared light modulated by the audio signal is applied to the surface of the infrared receiving tube, the receiving tube converts the received sound-modulated infrared light signal into an electrical signal, that is, generates an electrical signal having the same change rule as the audio signal at both ends of the receiving tube. The signal is coupled via C7 to power amplification to drive the speaker to sound.
The receiving circuit is shown in Figure 1.3.
1.2.3 relay node circuit
In the design of the relay node circuit, the transmitting circuit and the receiving circuit are integrated. The light-emitting diode and the photodiode have a vertical relationship, and it is good to change the communication direction by 90 degrees, and the distance can be extended to communicate.
The circuit diagram is shown in Figure 1.4.
2. System testing
Analysis of the test plan of the circuit:
(1) When inputting 800HZ tone signal at the transmitting end, test the effective value of the voltage outputted by the receiving end on the 8 ohm resistive load;
(2) When inputting 800HZ tone signal at the transmitting end, reduce the input signal of the transmitting end to 0V (that is, block the propagation path of infrared rays), and measure the noise voltage at the output end with the low frequency millivoltmeter.
3. Conclusion
Due to the reasonable design of the system architecture, the functional circuit is better, the communication performance is excellent and stable, and the basic requirements of the requirements of the topic and some of the requirements are well met. After testing and analysis, the system can realize: 1 transmission distance up to two meters, the restored audio signal has no obvious distortion; 2 when the single audio signal is input, the effective value of the output voltage is greater than 0.4V, the noise voltage is less than 0.1V; Indicates the presence or absence of the signal; 4 can realize relay forwarding, the communication direction changes by 90 degrees, and the signal can continue to be transmitted without obvious distortion.
Want to understand the use of TDA2822M integrated op amp and peripheral circuits to form the transmitting and receiving circuits of the infrared light-emitting tube as a communication device design, you can refer to the following article:
Design scheme based on infrared optical communication circuit
In addition, attached to the 2013 National College Student Electronic Competition Test Questions Group F: Design of Infrared Optical Communication Devices
2013-F-infrared optical communication device
Electronic Design Competition--Infrared Optical Communication Device Design Report
January 13, 2024
January 10, 2024
E-mail naar dit bedrijf
January 13, 2024
January 10, 2024
Telefoonnummer: 0511-86503898
Whatsapp: +8613775341656
Adres: NO.306 Yunyang Road,Danyang City, Jiangsu, China, Zhenjiang, Jiangsu China
website: https://nl.dyhorseoptical.com
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
